wooden surfaces

Pre - painting

  • Previously painted wooden surfaces must be thoroughly sanded to remove any dust or grease.
  • Apply Oil Primer by brush after thinning to given ratio by recommended thinner.
  • Allow it to dry for 6-8 hours before applying putty or lambi.
  • Sand the applied putty with sand paper no. 180 and apply 2nd coat of Oil Primer.
  • Begin painting the wooden surface with top coat.

 

Surface preparation

  • De-grease and de-rust ferrous metal substrates by suitable treatment.
  • For nonferrous metal substrates like aluminium, galvanised iron, tin, etc. pre-treat the surface with suitable Primer.
  • For ferrous metal substrates, apply Zinc Phosphate Primer either by brushing or spraying.
  • The use of Knifing Paste Filler is recommended to fill up dents and rectify surface imperfections.
  • Ensure that the surface is free from moisture and loose matter.
  • Apply one more coat of Zinc Phosphate Primer by brushing or spraying to cover puttied areas.
  • For best results, allow the primer coat to dry for 6 hours and dry sand with emery paper no. 320 before application of subsequent coat.

 

Painting

  • You can choose conventional enamels.
  • Apply wood primer by brush after thinning it to the specified ratio with the recommended thinner.
  • Allow it to dry for 6-8 hours, then apply putty or lambi.
  • Sand the applied putty with sand paper no. 180 and apply second coat of wood primer.
  • Now the wooden surface is ready for painting with the top coat.
  • Enamels are normally applied by brushing, although they can also be sprayed.
  • Enamels take longer to dry hence, extra care must be taken to ensure a dust-free environment while the paint is drying.
  • Two coats of paint is sufficient in most cases, however, if the earlier paint shade was significantly darker than the new one, an additional coat of paint is recommended.

 

Transparent finishes – Water Based

Surface preparation

  • The wooden surface to be coated/ painted must be seasoned (moisture level between 10-15%). It indicates proper level of moisture and treatment to prevent deformation in extreme hot/ cold climate.
  • In the case of new wood surface, sand the surface with emery paper along the direction of the grains of wood to remove the roughness.
  • Follow this by applying suitable wood putty. The purpose of the filler is to fill the grains and pores, and it should not be used as putty. The excess filler must be removed by strokes along the grain pattern. After 30 minutes, the filler may be applied again if required. Allow 2 to 3 hours drying time.
  • Sand the filled surface with emery paper no. 320
  • Apply 2 coats of Renner Water Based Wood Stain to get the preferred colour. Sand after the application of the 1st coat and keep 2-4 hours of interval between coats
  • If choosing Renner All In One Wood Finish (Stain + Sealer + Top Coat) then applying stain is not required

 

Painting

For New Wood

  • Ensure that the surface to be coated is free from dust
  • Apply Renner Water Based Exterior Top Coat or Renner All In One Wood Finish for exterior surfaces. Sand after the application of the 1st coat and keep 2-4 hours of interval between coats.
  • Apply Renner Water Based Interior Top Coat for Interior Surfaces.
  • Two to three coats of finish coating application are recommended to achieve the best results in terms of gloss and decorative appeal.
  • Containers should be tightly closed after use.

 

For Pre-Polished Wood

  • Sand the surface along the grains with emery paper no. 180 followed by no. 320 to get a smooth uniform surface.
  • If staining is desired, completely remove the old finish. Wipe the surface free of loose dust.
  • Proceed with the finish paint coats as explained above.

 

Transparent finishes – Solvent Based

Surface preparation

  • The wooden surface to be coated/ painted must be seasoned (moisture level between 10-15%). It indicates proper level of moisture and treatment to prevent deformation in extreme hot/ cold climate.
  • In the case of new wood surface, sand the surface with emery paper along the direction of the grains of wood to remove the roughness.
  • Follow this by applying suitable wood filler. The purpose of the filler is to fill the grains and pores, and it should not be used as putty. The excess filler must be removed by strokes along the grain pattern. After 30 minutes, the filler may be applied again if required. Allow 2 to 3 hours drying time.
  • Sand the filled surface with emery paper no. 320.
  • Apply 2 coats Asian Paints Sanding Sealer. Sand after the application of the 1st coat and keep 2-4 hours of interval between coats.

 

Painting

For New Wood

  • Ensure that the surface to be coated is free from dust.
  • Apply 2 coats of PU Top Coat. Sand after the application of the 1st coat and keep 2-4 hours of interval between coats.
  • Two to three coats of finish coating application are recommended to achieve the best results in terms of gloss and decorative appeal.
  • Containers should be tightly closed after use.

 

For Pre-Polished Wood

  • Sand the surface along the grains with emery paper no. 180 followed by no. 320 to get a smooth uniform surface
  • If staining is desired, completely remove the old finish. Wipe the surface free of loose dust.
  • Proceed with the finish paint coats as explained above.
Image