While painting your home, stay away from the hassle of wiping paint stains from furniture, fans, chandeliers etc. by covering them with old cloth or plastic. Be sure to wipe out the paint drips from the floor immediately.
For water based paints:
Wet condition: wash with cold water immediately and wipe with clean cloth.
Dried film: Soak the drip with water or dilute detergent solution. The film should be scraped off with a suitable scraper. While scratching, ensure not to damage the value and appearance of the substrate, especially in case of wooden, marble or valuable metal articles / substrates.
For solvent based paints:
Wet condition: wash immediately with mineral turpentine oil and wipe with clean cloth.
Dried film: The drip should be soaked with mineral turpentine. If the stain has dried for over two days, soak the stain with Xylene. Then, scratch the film using a suitable scraper. While scratching, ensure not to damage the value and appearance of the substrate, especially in case of wooden, marble or valuable metal articles / substrates. Wipe the area with water or dilute detergent solution and leave it to dry.
For wood finishes
Wet condition: Clean the PU stains by soaking with PU Thinner no. 338 and then wiping with a clean cloth.
Recoat a painted / polished wood with clear finish: Apply paint remover / stripper on the surface. Scrape the peeled coating from the surface of wood. Clean the surface with a thinner to remove traces of paint film and residual paint remover / material. Allow sufficient time (overnight) before applying any coating.
Change colour of wood: Remove the colour with paint remover. However, if the stain is directly on the wood, removing it will be difficult. In such cases, you can apply the same stain or a darker one during recoating.
Clean drips of PU on wooden articles, floor, tiles: It is difficult to remove drip marks from wooden surfaces. If the paint has penetrated through the surface then the entire film has to be removed and recoated. It can be done using a scraper or files (available at hardware stores), gently without damaging the wood. Follow it up with sanding using emery paper no. 180 and continue normal application of the wood finish. Drip marks on the floor / tiles can be removed by carefully scraping with a putty knife or scraper. However, mask the area near the coating surface as scraping PU coating can be time consuming.
Clean wax drips: Carefully scrape out as much solid wax as possible. Once the surface is sufficiently clean, place a freezer bag of ice cubes over the affected area for several minutes. The cold makes the wax more brittle. Now you can use a butter knife to scrape off additional residue. Finally, apply the warm-hot method. Use a hair dryer to soften the remaining material and scrape it off. Or place a very absorbent material like a thick paper towel (or napkin) on the spill and run a hot iron on it. The wax will melt and get absorbed by the material.
Remove water based paint: Scrape off as much paint as possible with an old knife. Using a cloth or sponge dipped in the solution (a cup of warm water and a spoon of dish detergent, no bleach), dab the stain working from the outside in. Soak it for longer if the paint does not start to dissolve in soapy water. When the paint starts to dissolve, use a tissue to absorb the paint-filled fluid that is left as residue. You can also use clean water to clean the surface. Make sure to always blot and not pour water as it may lead to saturation of the carpet and the stain might spread.
Remove oil based paint: Use solvents like mineral turpentine, methylated spirit or a dry cleaning solvent to remove such paints. Just like in water-based coatings, dampen a rag and dab the paint stain from the outside in, without spreading the stain. Use a detergent solution to remove the dissolved paint.
Remove mildew from bathroom: Use an old toothbrush to scrub off mildew from the grout between tiles. For more stubborn stains cover it with a paste of scouring powder that contains bleach and leave it covered for a few hours. Scrub and rinse clean. After using the shower, leave the door or curtain open. Wipe the walls to dry them. Close the shower door or curtain to allow that to dry also.